Document ID: 310442
http://support.veritas.com/docs/310442 E-Mail Colleague IconE-Mail this document to a colleague

Disaster recovery for Exchange
Details:

Disaster recovery for Exchange
This procedure guides you through a complete restoration of Exchange using Backup Exec. You should have already performed all the appropriate preparation.
See Preparing for disaster recovery of Exchange Server.
 http://support.veritas.com/docs/310443
If the Exchange 2000 Server being recovered contains the Site Replication Service (SRS) and/or Key Management Service (KMS), then before you begin the disaster recovery, refer to your Exchange documentation for details on recovering those databases.
Always log in to Windows using the Administrator account (or an Administrator equivalent) during this procedure. Other requirements include:
- The storage groups and databases must already exist on the target server, and have the same names as the original storage groups or databases.
- The destination server must have the same Organization and Administrative Group name as the source server.
- The destination databases must be configured so that they can be overwritten.
See Configuring a database in Exchange 2000, 2003, and 2007.
 http://support.veritas.com/docs/310058
You can use Intelligent Disaster Recovery to recover the Exchange server.
See About Microsoft Exchange recovery notes.
 http://support.veritas.com/docs/310580
To perform disaster recovery for Exchange 2000 or later
1. Recover the Windows server first.
See Returning to the last known good configuration.
 http://support.veritas.com/docs/309701
Make sure you restore the Exchange Server 2000 Server or later files that existed on all disk partitions.
When the Windows 2000 server disaster recovery procedure is complete (after the last reboot), you must recover the Exchange server.
2. From the Services applet, verify the Microsoft Exchange Information Store service is started.
3. Start Backup Exec.
4. Catalog the media that contains the latest backup of the Exchange 2000 Server or later storage groups you want to recover.
5. On the navigation bar, click the arrow next to Restore.
6. Click New Restore Job.
7. On the Properties pane, under Source, click Selections.
8. Select the latest full backups of each storage group for restore.
If continuous protection is enabled, you can select the backup sets from a full backup or a recovery point.
If the Exchange 2000 Server being recovered contains the Site Replication Service (SRS) and/or Key Management Service (KMS), then select those databases for restore as well.
9. If necessary, select all subsequent incremental storage group backups.
If differential backups are to be restored, only the most recent differential storage group backups need to be selected.
10. On the Properties pane, under Settings, click Microsoft Exchange.
11. Click the Purge existing data and restore only the databases and transaction logs from the backup sets option.
12. In the Path on Exchange Server for temporary storage of log and patch files field, type a location where the associated log and patch files are to be kept until the database is restored.
Make sure the temporary location for log and patch files is empty before you start a restore job. If a restore job fails, check the temporary location (including subdirectories) to make sure any previous log and patch files from a previous restore job were deleted.
13. If your selection contains the last backup set to be restored, check Commit after restore completes.
Do not check this if you still have backup sets to restore.
If Commit after restore completes is checked when an intermediate backup is being applied, you cannot continue to restore backups and you must restart the restore operation from the beginning.
After the database is restored, the log and patch files in the temporary location are applied to the database, and then the current log files are applied. After the restore is complete, the log and patch files are automatically deleted from the temporary location (including any subdirectories).
14. If you want the databases to be immediately available to users after the recovery, check Mount database after restore.
15. Start the restore job or select other restore options on the Properties pane.
16. After completing the restore, it is recommended that a full backup of the restored databases be performed.



Supplemental Material:

System: Ref.#Description
Vasont ID: v12009246_corsicaweb

Products Applied:
 Backup Exec for Windows Servers 12.5
Last Updated: August 05 2009 02:03 PM GMT
Expires on: 365 days from publish date
Subscribe Via E-Mail IconSubscribe to receive critical updates about this document

Subjects:
 Backup Exec for Windows Servers
   Information Development: Agents
Windows NT Small Business Server
   Information Development: Agents

Languages:
 English (US)

Operating Systems:
Windows 2000

Professional, Server

Windows NT Small Business Server

2000

Windows XP

Pro 5.1, Pro 5.1 64 bit SP1, Pro 5.1 64 bit SP2, Pro 5.1 64-bit, Pro 5.1 SP1, Pro 5.1 SP2

Windows Server 2003

DataCenter, DataCenter (IA64), DataCenter (x64), DataCenter SP1, DataCenter SP1(IA64), DataCenter SP1(x64), DataCenter SP2, Datacenter SP2(x64), Enterprise (IA64), Enterprise (x64), Enterprise SP1(IA64), Enterprise SP1(x64), Enterprise SP2, Enterprise SP2(x64), Enterprise Server, Enterprise ServerSP1, R2, Standard Server, Standard Server SP1, Standard Server SP1 (x64), Standard Server SP2, Standard Server SP2 (x64), Standard Server(x64), Storage Server, Storage Server SP1, Storage Server SP2, Web Server, Web Server SP1, Web Server SP2

Windows Server 2008

DataCenter (x64-64bit), DataCenter (x86-32bit), Enterprise (x64-64bit), Enterprise (x86-32bit), Itanium, Standard (x64-64bit), Standard (x86-32bit), Web Server (x64-64bit), Web Server (x86-32bit)